No-clean vloeibare flux 100ml
Details
Medium-active 'no-clean' flux, geschikt voor het solderen. De vloeistof is een oplossing van 24% hars in alcohol.
Prima geschikt voor SMD werkzaamheden, maar in het bijzonder ook geschikt bij het reworken van oude en/of geoxideerde PCBs vanwege de krachtige activatie.
De flux wordt geleverd in een flesje. Aan de binnenkant van de dop zit een handig kwastje voor het aanbrengen van de flux.
Specificaties
Inhoud | 100 ml |
Flux type | 24% hars in alcohol |
Voldoet aan | ISO 9454-1 type 1.1.2 / 3 A |
Merk | Termopasty |
Type | TK83 |
Downloads
Technical data sheet TK83 |
(243.59 KB) | Download |
Nieuwste reviews
Lees alle reviews (10)
Review door Arco
Geplaatst op 28-01-2024
Het werkt best prima, maar ik heb betere ervaring met de RF800 die ook verkocht wordt. Die vind ik net even wat makkelijker werken.
Review door J. Rozema
Geplaatst op 25-09-2022
Review door Ward
Geplaatst op 20-07-2022
Opzich prima spul, vioolhars uit doseerspuit op gel basis laat de tin een stuk beter vloeien (verdampt ook minder snel), dit puur gekocht voor contacten met corrosie. laat inderdaad een flink plakkerig residu achter (erger dan bij soldeerpasta)
Review door S. Smeenk
Geplaatst op 27-04-2022
Review door Robert Jan Bout
Geplaatst op 20-12-2021
Het ruikt niet optimaal maar is ook niet slecht. Vloeit goed op 350 graden. Verpakking geeft 250 graden aan oid, maar dat geeft alleen een langere verwerkingstijd. Nadeel is wel dat het slecht schoon te maken is en dat het nogal plakkerig is.
Review door Wil Thimister
Geplaatst op 03-09-2021
Review door Rolf
Geplaatst op 20-01-2021
Zeer slecht schoon te maken. Veel na werk.
Plakt om het leven.
Geen klachten over soldeer eigenschappen.
Plakt om het leven.
Geen klachten over soldeer eigenschappen.
Review door h_c
Geplaatst op 10-11-2020
Review door Darko Markovic
Geplaatst op 21-08-2019
It works just fine. It helps the process of de-oxidizing greatly and makes things simpler.
Now regarding to "no clean" part. Well if you use proper amount of it you might end up with no clean situation. But usually well you have to clean it of the board. Is it going to be a brush or a clean room wipe or IPA with hot air does not matter it will clean very easy and good.Just use small amounts a time until you have enough for the job at hand.Do not try to put more on the brush as it fits. Just take it to the bottle few more times and you will get to the right amount. Or use some other way to dispense it.
Any ways this No Clean rant is just smallest issue possible. It is more than good enough just as not as good as high end gel stuff.
So if you expect it to be as "no clean" as those expensive gels you might be little disappointed. But if you learn how to use it you will be more then satisfied especially for the low price per mL of flux.
Also do not forget that disregarding does it smells good or bad (this one smells like IPA) you will need a fume extractor.
Remember higher the temperature goes fluxes will be harder to work with. They will evaporate faster and burn creating to much fumes that are not healthy.
Now regarding to "no clean" part. Well if you use proper amount of it you might end up with no clean situation. But usually well you have to clean it of the board. Is it going to be a brush or a clean room wipe or IPA with hot air does not matter it will clean very easy and good.Just use small amounts a time until you have enough for the job at hand.Do not try to put more on the brush as it fits. Just take it to the bottle few more times and you will get to the right amount. Or use some other way to dispense it.
Any ways this No Clean rant is just smallest issue possible. It is more than good enough just as not as good as high end gel stuff.
So if you expect it to be as "no clean" as those expensive gels you might be little disappointed. But if you learn how to use it you will be more then satisfied especially for the low price per mL of flux.
Also do not forget that disregarding does it smells good or bad (this one smells like IPA) you will need a fume extractor.
Remember higher the temperature goes fluxes will be harder to work with. They will evaporate faster and burn creating to much fumes that are not healthy.
Review door Robin Degen
Geplaatst op 08-04-2018