Voor wat het kost, is het fantastisch.
De filter, daar kijk je bijna door, is een soort spons. Maar wat had je verwacht? Er zit nog een vervanger bij.
Ik denk dat ik het gewoon op de stofzuiger hou want als je niet helemaal onder de kap soldeert dan stijgt de rook nog op
Aoyue 486+ soldeerdampafzuiging
Details
De Aoyue 486+ soldeerdamp afzuiger komt met een LED lamp en een aluminium slang van 1,8 meter lang. Deze afzuiger beschikt over een geactiveerd koolstof filter, waarmee de deeltjes worden opgevangen. Het filter is geheel uitwasbaar. De afzuiger beschikt over een stabiele standaard. Voordelige oplossing om een groot deel van de nare dampen te filteren en af te voeren.
Specificaties
Vermogen | 20 W |
Filter | Geactiveerd koolstof filter van 120 x 120 mm |
Buitenmaat afmeting | 200 x 170 x 90 mm |
Lengte buis | 30 cm |
Diameter buis | 10 cm |
Plus en minpunten
- LED lamp
- Zeer voordelig
- Beperkte afzuigkracht
- Filtert minder dan veel duurdere oplossingen
Vergelijkbare producten
Nieuwste reviews
Review door Staf Van Lierde
Geplaatst op 12-09-2022
Review door Vasco
Geplaatst op 16-02-2021
Apparaat moet letterlijk boven de soldeertang hangen om effectief rook af te zuigen en zit dan in de weg.
Review door b ijsinga
Geplaatst op 27-01-2021
Wordt gebruikt op vso school voor afzuigen rook bij figuren houtbranden. Zuigt voldoende afmet eerkstuk er onder houden. Met filter af nog beter. Rook rechtstreeks naar buiten. Klem om slang vast te zetten te klein. Al met al ben er blij mee. Gemakkelujk aan en uit voor de leerlingen. Verlichting mooi mee genomen. Goede verlichting.
Review door Kai Michel
Geplaatst op 04-01-2021
Review door Sandra Oud
Geplaatst op 01-12-2020
Het is een handig apparaat, gemakkelijk in gebruik. Echter is de afzuiging niet sterk maar voor een hobbyist toch best redelijk, ik ben er blij mee
Review door Tony
Geplaatst op 01-05-2020
Zuigkracht niet geweldig, maar het hoeft ook niet te tochten, de lamp is een echte plus.
komt met extra filter, netjes.
snoer is wat aan de zware kant, dit was niet nodig het is geen zware stroomverbruiker.
tervrede met de aanschaf
komt met extra filter, netjes.
snoer is wat aan de zware kant, dit was niet nodig het is geen zware stroomverbruiker.
tervrede met de aanschaf
Review door Darko Markovic
Geplaatst op 13-08-2019
It works and it is practical with LED light and filter and pipe. Can't beat it's price. Good Value for the money. Build to price and bit above it. Light and it's switch look like an afterthought but execution was good.
Stand is limited but high enough for usage on the table.
Now all that said it is still cheaper solution and solution for hobby people. If I would need to work with it 8 hours a day I would not be able to stand it's sound. It is a bit louder than what I've expected. You need to position it correctly or fumes will escape. But than again it's same with so many other solutions. Most of the cheaper solutions are as loud or louder and even some higher costs solution are sounding bad. It will filter and remove the fumes from your working station. I would advice using small fan on the opposite side helping directing air towards the fume extractor. Something quiet if possible.
Way better and healthier than breathing in burned resin and having headache. If you get some headache from the noise at least it is not going to poison you :)
Everyone soldering should have some fume extraction solution. This is one solution that is affordable and you can make it work for you.
Stand is limited but high enough for usage on the table.
Now all that said it is still cheaper solution and solution for hobby people. If I would need to work with it 8 hours a day I would not be able to stand it's sound. It is a bit louder than what I've expected. You need to position it correctly or fumes will escape. But than again it's same with so many other solutions. Most of the cheaper solutions are as loud or louder and even some higher costs solution are sounding bad. It will filter and remove the fumes from your working station. I would advice using small fan on the opposite side helping directing air towards the fume extractor. Something quiet if possible.
Way better and healthier than breathing in burned resin and having headache. If you get some headache from the noise at least it is not going to poison you :)
Everyone soldering should have some fume extraction solution. This is one solution that is affordable and you can make it work for you.
Review door Paul Langemeijer
Geplaatst op 08-05-2019
Doet het helemaal goed. Verlichting is een pluspunt.